TMCP工艺下Ti-Mg氧化物冶金钢轧态组织性能

摘要：为研究轧制过程中氧化物粒子对母材组织性能的影响，提出了一种只在再结晶区进行轧制的新工艺路线，利用常规冶炼及氧化物冶炼的实验钢分析其轧态显微组织、力学性能及相变过程。结果表明：在新轧制工艺下，氧化物冶金钢母材显微组织由常规的贝氏体板条束变为针状铁素体，其基体具有良好的力学性能，-80℃冲击韧性达149J；热轧工艺下的组织转变分两阶段进行，初期是针状铁素体的形核和晶粒细化，之后贝氏体相变被限制在针状铁素体板条间构成的区域内。     

Coexistence of antiferro- and ferrimagnetism in the spinel ZnFe2O4 with an inversion degree δ lower than 0.3

Samples with inversion parameter values (δ) ranging from 0.27 to 0.14 while maintaining the crystallite size value have been successfully fabricated from commercially available powders by mechanical grinding and thermal annealing treatments at temperatures ranging between 400 and 600 °C. Detailed characterization studies of these samples using X-ray, neutron diffraction and magnetic measurements have confirmed for the first time the simultaneous coexistence at 2 K of short range antiferromagnetic and ferrimagnetic ordering for a wide range of the inversion parameter. The magnetic phase diagram obtained is different from the one previously reported, which shows at 2 K the coexistence of long range antiferromagnetic order and short range order for values of inversion parameters less than 0.1 and the presence of a ferrimagnetic order only for values of δ > 0.2. At room temperature, the Rietveld analysis of NPD patterns and the magnetization curves showed a paramagnetic behavior in the samples with δ ≤ 0.1. For the samples with higher cationic inversion, typical hysteresis curves of ferrimagnetic materials were observed and the saturation magnetization values obtained agree quite well with the net magnetic moment obtained from the Rietveld refinement of the neutron diffraction patterns.     

铁素体基Ti-Mo高强钢连续冷却相变及组织性能

摘要：为了深入了解铁素体基Ti-Mo高强钢在连续冷却相变过程中组织及硬度的变化及其原因，通过热膨胀法、金相及硬度等实验研究了Ti-Mo微合金钢在连续冷却条件下组织及性能的变化，探讨了冷却速率对组织、硬度及相变行为的影响机理，揭示了（Ti，Mo）C在奥氏体和铁素体中Ti/Mo原子比变化的原因。结果表明，随着冷却速率由0.06℃/s增加至17.9℃/s，组织依次为多边形铁素体+珠光体→多边形铁素体+粒状贝氏体→粒状贝氏体，硬度由144HV逐渐增大至228HV。当冷速由0.14℃/s增大至0.90℃/s时，组织中多边形铁素体比例不断增大，珠光体比例不断降低，硬度的提高主要来自于铁素体晶粒尺寸的细化及纳米级（Ti，Mo）C粒子的增多；当冷速由1.79℃/s增大至17.9℃/s时，组织中多边形铁素体比例不断降低，贝氏体比例不断提高，硬度的提高主要是由于贝氏体组织的细化及其比例的增加。（Ti，Mo）C粒子主要有2类：一类是奥氏体中析出的10～20nm的粒子，Ti原子数分数约为88%，另一类是铁素体中析出的小于10nm的粒子，Ti原子数分数约为68%，EDS测量结果与计算结果大致相当。     

Synthesis and magnetic properties of nano-sized Cu0.5Ni0.5Fe2O4 via citrate and aloe vera: A comparative study

In this report, Cu_0.5Ni_0.5Fe₂O₄ nanoparticles were synthesized by solgel using eco-friendly aloe vera extract and citric acid separately and their properties were discussed. Structural, Functional, morphological, magnetic properties of the samples were characterized using X-ray diffraction (XRD), Fourier transform infrared (FT-IR), Transmission electron microscopy (TEM), Vibrating sample magnetometer (VSM). XRD exhibited the samples have single phase cubic spinel with average size of 46.4?nm and 35.45?nm. Two characteristics bands of ferrite were confirmed by FTIR. TEM indicated different morphology of the samples with some regularity. VSM data showed that higher coercivity for the sample prepared by aloe vera extract.     

Magnetic properties and magnetoresistance effect of SnFe2O4 spinel nanoparticles: Experimental,ab initio and Monte Carlo simulation

In this contribution, SnFe₂O₄ nanoparticles were prepared by the solvothermal method, the structural properties were performed using X-Ray Diffraction (DRX) to prove the success of tin ferrite formation and to determine de crystals parameters. The size and morphological study were build using Scanning Electron Microscopy (SEM) and Transmission Electron microscopy (TEM), the results showed that the size of particles is uniform with a range of particles (5–7 nm). The magnetic properties were carried out using the SQUID device, the SnFe2O4 nanoparticles have a magnetic transition at 750 K. In addition, the hysteresis loops at low temperature displayed Ms and Mr equals to 23 emu/g and 6 emu/g, respectively. The magnetoresistance properties were investigated, the SnFe₂O₄ nanoparticles present a large magnetoresistance effect (80%). The experimental results are supplemented by model calculations utilizing density functional theory and Monte-Carlo simulations.     

Salt-assisted solution combustion synthesis of NiFe2O4: Effect of salt type

The effects of three types of salt including NaF, KCl, and NaCl on the properties of NiFe₂O₄ nanoparticles using salt-assisted solution combustion synthesis (SSCS) have been investigated. The synthesized powders were evaluated by SEM, TEM, FTIR, XRD, and VSM analysis. Also, the specific surface area (SSA), as well as size distribution and volume of the porosities of NiFe₂O₄ powders were determined by the BET apparatus. The visual observations showed that the intensity and time of combustion synthesis of nanoparticles have been severely influenced by the type of salt. The highest crystallinity was observed in the synthesized powder using NaCl. The SSA has also been correlated completely to the type of salt. The quantities of SSA was achieved about 91.62, 64.88, and 47.22 m²g^-1 for the powders synthesized by KCl, NaCl, and NaF respectively. Although the magnetic hysteresis loops showed the soft ferromagnetic behavior of the NiFe₂O₄ nanoparticles in all conditions, KCl salt could produce the particles with the least coercivity and remanent magnetization. Based on the present study, the salt type is a key parameter in the SSCS process for the preparation of spinel ferrites. Thermodynamic evaluation also showed that the melting point and heat capacity are important parameters for the proper selection of the salt.     

Synthesis,characterization and magnetic properties of polythiophene/SrFe12-x(ZrZn)0.5xO19 nanocomposite as a microwave absorber

Ferrites are an important group of magnetic materials which are used as absorbers. The incorporation of ferrite and conducting polymer achieves great enhancement in microwave absorption properties. The nanocomposites of hexagonal ferrites embedded by conducting polymers such as polypyrrole, polyaniline and polythiophene (PTH) have been paid much attention. In the present study, strontium hexagonal ferrite doped by Zr and Zn with the final formula of SrFe_12-x(ZrZn)_0.5xO19 considering x = 0.9 and embedded by PTH was produced to achieve a nanocomposite with the highest microwave absorbing ability. In this study, after synthesis of SrFe₁₂O₁₉(ZrZn)_0.5xO19 and PTH, the nanocomposite was prepared by in situ polymerization. Wrapping the ferrite particles and PTH chains could form nanocomposite properly, and therefore acceptable interactions were observable between SrFe_12-x(ZrZn)_0.5xO19ferrite particles and PTH polymer chains in the composites. Assessing the X-ray diffraction (XRD) patterns of SrFe_12-x(ZrZn)_0.5xO19, PTH, and PTH/SrFe_12-x(ZrZn)_0.5xO19 nanocomposite indicated that the PTH characteristic peak shifts slightly and its peak intensity reduces, which may be attribute to the coating of PTH polymer chains onto SrFe_12-x(ZrZn)_0.5xO19 particles. We revealed also lower magnetic properties in the obtained nanocomposite. The morphological assessment also suggested that PTH could effectively coat the SrFe_12-x(ZrZn)_0.5xO19 particles. The synergistic effect of SrFe_12-x(ZrZn)_0.5xO19 particle plus PTH leads to microwave absorption percentage higher than 95% by PTH/SrFe_12-x(ZrZn)_0.5xO19 nanocomposite. Overall, nanocomposite creating by coupling interaction between SrFe_12-x(ZrZn)_0.5xO19 particles (x = 0.9) and PTH can effectively lead to achieve the highest rate of absorption of electromagnetic waves.     

Heterostructured thin LaFeO3/g-C3N4 films for efficient photoelectrochemical hydrogen evolution

The deposition of LaFeO₃ at the surface of a graphitic carbon nitride (g-C₃N₄) film via magnetron sputtering followed by oxidation for photoelectrochemical (PEC) water splitting is reported. The LaFeO₃/g-C₃N₄ film was investigated by various characterization techniques including SEM, XRD, Raman spectroscopy, XPS and photo-electrochemical measurements. Our results show that the hydrogen production rate of a g-C₃N₄ film covered by a LaFeO₃ film, exhibiting both a thickness of ca. 50 nm, is of 10.8 μmol h⁻¹ cm⁻² under visible light irradiation. This value is ca. 70% higher than that measured for pure LaFeO₃ and g-C₃N₄ films and confirms the effective separation of electron-hole pairs at the interface of LaFeO₃/g-C₃N₄ films. Moreover, the LaFeO₃/g-C₃N₄ films were demonstrated to be stable and retained a high activity (ca. 70%) after the third reuse.     

Structural,magnetic, thermal and optical properties of Sn2+ cation doped magnetite nanoparticles

Tin doped nanomagnetites, Sn_xFe_3-xO₄, were synthesized with various concentrations of Sn²⁺ ion (x = 0.0, 0.2, 0.4, 0.6, 0.8, 1.0) by co-precipitation method. XRD, VSM, TG-DTA, SEM-EDX and UV–Vis were used to characterize and study the structural, magnetic, thermal, and optical properties of Sn_xFe_3-xO₄ nanoparticles. XRD confirmed the presence of cubic structure and spinel phase of tin doped magnetites. The d-spacing, lattice parameter, density, crystallite size and cation distribution were derived from the XRD analysis. The M − H curves exhibited changes in saturation magnetization (M_s), coercive field (H_c), remanent magnetization (M_r) and susceptibility (χ), with increasing concentration of non-magnetic Sn²⁺ ions. Differential thermal analysis was used to study the thermal stability of Sn_xFe_3-xO₄ nanoparticles. The SEM images revealed the surface morphology of the nanoparticles and the EDX spectra showed an increase in the Sn content and a corresponding decrease in the Fe content for the tin doped samples. The optical bandgap was found to be centered at 3.9 eV for the synthesized materials. This systematic study may be the first comprehensive report on synthesis and characterization of tin doped magnetites.